23MPa High Pressure Airless Paint Spray Gun Wall Paint Spray Gun 2200W 3000PSI. The Airless Paint Sprayer is suitable for most paint, except solid and particle paint.Please clean the machine after spayer otherwise it will remain stuck after a long time. Flow: 1.8L / min. Hose: High pressure pipe can receive up to 30 meters. Large outlet pressure: 3000 (N / S).
16, Size:50x45x50cm(19.68x17.7x19.68 inch). All stainless steel suction pump body, highly sealed and durable. Main pump body has been Extremely heat treatment , corrosion resistant, wear resistant. Humanized independent handle, soft plastic design.
One-way sealed pressure relief valve, full copper valve core, tungsten steel seal, safe and durable. Mechanical pressure sensing twisting, anti-mouth design. High horsepower turbine exhaust fan for fast heat dissipation and protection of the motor.
8.2 times of polycondensation and filtration of impurities to make the spraying smoother. 1PC 10 m high pressure pipe. Electric plunger sprayer operation precautions. First check for impurities such as foam in each tube (including the position of the pump under the machine) to ensure that there are no impurities before the tube is installed. When inserting the feeding tube, it is a little tight.
It cannot be hard inserted to avoid the front two o-rings being broken. It is recommended to apply some detergent or lubricating oil on the pump body and the feeding tube under the machine (lubricating oil is not included in the product) , the suction tube must be inserted in place.When connecting the high pressure pipe, the screws on both ends must be straightened and then tightened with a wrench (no need for any gasket). There must be a crescent-shaped gasket at the nozzle position. The nut of the nozzle holder should be tightened to prevent water leakage. When pulling (rotating) the nozzle, the large nut of the nozzle holder should be loosened and pulled out. Pull the nozzle (beware of a small gasket inside). Turn on the valve with the return valve open. Start the return pipe with liquid discharge, and then close the return valve (if the return pipe only emits air without liquid, indicating that the feed pipe is not installed, please check the tightness of the feed pipe). Close the return valve, the machine will stop when it reaches a certain pressure, so that you can start working.
Pressure regulating valve, adjust pressure according to your own needs. The pump body filler on the machine is recommended to use oil once every time (anti-wear hydraulic oil). Shutdown needs to turn off the power switch without unplugging the power supply. Be sure to first put the air pressure in the gun to 0, then open the discharge valve, and finally unplug the power supply. There is residual pressure in the machine after shutting down.
It is not possible to relieve pressure through the return valve and pressure regulating valve. It can only be relieved by the spray gun. If the operation is improper, it will directly cause the return valve and the pressure regulating valve to be damaged by the residual pressure!
The machine can not be idling for more than 30 seconds, or usually used to spray water! Always point hydraulic oil to the pump body to extend its life!
Feedback is very important to us. It is impossible to address issues if we do not know about them!
Please keep the original box or packaging within 15days since item received. Your satisfaction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount.
Due to time zones, our reply to your questions may not be immediately. If it's non-workdays, please kindly be patient and wait till Monday. The item "23MPa High Pressure Airless Paint Spray Gun Wall Paint Spray Gun 2200W 3000PSI" is in sale since Monday, August 3, 2020. This item is in the category "Home, Furniture & DIY\DIY Materials\Paint Sprayers & Accessories\Paint Sprayers". The seller is "aplus-bargain" and is located in Lausanne.
This item can be shipped to all countries in Europe.