Specification: Model: H-780 The nozzle diameter: 0.15mm0.2mm Power: 1800W The best spray distance: 350mm400mm Voltage: 220V/50HZ Maximum flow: 2.8L/Min Maximum pressure:22Mpa Spraying width: 250mm Package Size:435048cm Weight: 20KG Details: 1. Alloy portable handle design for easy movement 2. The pressure regulating valve can be rotated to easily adjust the pressure 3. Power switch silicone cover can be dustproof and waterproof 4. Shockproof pressure gauge enables simple monitoring of pressure and safer construction 5.
Feeding port and discharge port is made of high quality materials and is wear resistant. The return switch can be turned on or off with ease and is convenient and practical. Fine filter mesh for easy filtration to prevent foreign matter from entering the machine. 22Mpa 1800W High Pressure Airless Wall Paint Spray Gun Sprayer Spraying Machine.The Nozzle Diameter: 0.15mm0.2mm. The Best Spray Distance: 350mm400mm. Alloy Portable Handle Design for Easy Movement. The Pressure Regulating Valve Can Be Rotated to Easily Adjust the Pressure. Power Switch Silicone Cover Can Be Dustproof and Waterproof. Shockproof Pressure Gauge Enables Simple Monitoring of Pressure and Safer Construction. Feeding Port and Discharge Port Is Made of High Quality Materials and Is Wear Resistant.
The Return Switch Can Be Turned on or off with Ease and Is Convenient and Practical. Fine Filter Mesh for Easy Filtration to Prevent Foreign Matter from Entering the Machine. The Airless Paint Sprayer is suitable for most paint, except solid and particle paint. Please clean the machine after spayer otherwise it will remain stuck after a long time. Note:It is not recommended to use floor paint or thick waterproof material; it is recommended to use latex paint or paint of the same concentration as latex paint.Electric Plunger Sprayer Operation Precautions. First Check for Impurities Such As Foam in Each Tube (Including the Position of the Pump Under the Machine) to Ensure That There Are No Impurities Before the Tube Is Installed. When Inserting the Feeding Tube, It Is a Little Tight. It Cannot Be Hard Inserted to Avoid the Front Two O-rings Being Broken. It Is Recommended to Apply some Detergent or Lubricating Oil on the Pump Body and the Feeding Tube Under the Machine (Lubricating Oil Is Not Included in the Product), the Suction Tube Must Be Inserted in Place. When Connecting the High Pressure Pipe, the Screws on Both Ends Must Be Straightened and Then Tightened with a Wrench (No Need for Any Gasket). There Must Be a Crescent-shaped Gasket at the Nozzle Position. The Nut of the Nozzle Holder Should Be Tightened to Prevent Water Leakage. When Pulling (Rotating) the Nozzle, the Large Nut of the Nozzle Holder Should Be Loosened and Pulled out.
Pull the Nozzle (Beware of a Small Gasket Inside). Turn on the Valve with the Return Valve Open.Start the Return Pipe with Liquid Discharge, and Then Close the Return Valve (If the Return Pipe Only Emits Air Without Liquid, Indicating That the Feed Pipe Is Not Installed, Please Check the Tightness of the Feed Pipe). Close the Return Valve, the Machine Will Stop When It Reaches a Certain Pressure, so That You Can Start Working.
Pressure Regulating Valve, Adjust Pressure According to Your Own Needs. The Pump Body Filler on the Machine Is Recommended to Use Oil Once Every Time (Anti-wear Hydraulic Oil). Shutdown Needs to Turn off the Power Switch Without Unplugging the Power Supply. Be Sure to First Put the Air Pressure in the Gun to 0, Then Open the Discharge Valve, and Finally Unplug the Power Supply.
There Is Residual Pressure in the Machine After Shutting down. It Is Not Possible to Relieve Pressure Through the Return Valve and Pressure Regulating Valve.
It Can Only Be Relieved by the Spray Gun. If the Operation Is Improper, It Will Directly Cause the Return Valve and the Pressure Regulating Valve to Be Damaged by the Residual Pressure!
The Machine Can Not Be Idling for More than 30 Seconds, or Usually Used to Spray Water! Always Point Hydraulic Oil to the Pump Body to Extend Its Life! Feedback is very important to us.
It is impossible to address issues if we do not know about them! Please keep the original box or packaging within 15days since item received. Your satisfaction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount.Due to time zones, our reply to your questions may not be immediately. If it's non-workdays, please kindly be patient and wait till Monday. This item is in the category "Home, Furniture & DIY\DIY Materials\Paint Sprayers & Accessories\Paint Sprayers". The seller is "rukfighting123" and is located in this country: GB. This item can be shipped to United Kingdom.