Mpa High Pressure

220V 1.8KW High Pressure Diving Breath Air Pump Air Compressor 2800r/min 30MPA


220V 1.8KW High Pressure Diving Breath Air Pump Air Compressor 2800r/min 30MPA
220V 1.8KW High Pressure Diving Breath Air Pump Air Compressor 2800r/min 30MPA
220V 1.8KW High Pressure Diving Breath Air Pump Air Compressor 2800r/min 30MPA
220V 1.8KW High Pressure Diving Breath Air Pump Air Compressor 2800r/min 30MPA
220V 1.8KW High Pressure Diving Breath Air Pump Air Compressor 2800r/min 30MPA
220V 1.8KW High Pressure Diving Breath Air Pump Air Compressor 2800r/min 30MPA
220V 1.8KW High Pressure Diving Breath Air Pump Air Compressor 2800r/min 30MPA
220V 1.8KW High Pressure Diving Breath Air Pump Air Compressor 2800r/min 30MPA
220V 1.8KW High Pressure Diving Breath Air Pump Air Compressor 2800r/min 30MPA
220V 1.8KW High Pressure Diving Breath Air Pump Air Compressor 2800r/min 30MPA
220V 1.8KW High Pressure Diving Breath Air Pump Air Compressor 2800r/min 30MPA

220V 1.8KW High Pressure Diving Breath Air Pump Air Compressor 2800r/min 30MPA    220V 1.8KW High Pressure Diving Breath Air Pump Air Compressor 2800r/min 30MPA

220V 1.8KW High Pressure Diving Breath Air Pump Air Compressor 2800r/min 30MPA. 1.8KW High Pressure Diving Breath Air Pump Air Compressor 2800r/min 30MPA 220V. Motor speed: 2800r / min. Air output: 130L / min.

Motor material: all copper coil. Cylinder head material: cast aluminum. Connector type: 8mm quick connect female. Package size: 49 28.5 43cm.

Use car or motorcycle engine oil, or piston air compressor oil. Oil: add piston type air compressor oil (the machine has no oil, because it is not allowed to carry oil by air). Speed test: it takes 3 minutes for 0.5L oxygen cylinder to inflate 30MPa, 6 minutes for 1L oxygen cylinder to inflate 30MPa, and 40 minutes for 6.8L oxygen cylinder to inflate 30MPa.

Operation method of electric air pump. Check the amount of oil before each use, the oil should exceed the red dot, but not too much. The Lubricating oil that is exported to foreign countries is taken out and needs to be added by itself. Change the oil cover used for transportation to a strip-shaped breathing plug.

Loosen the air bleed screws on both sides before starting the machineRemember, the machine needs to start under zero pressure. If the bleeder screw is not loosened, the machine will not start. After starting the machine, tighten the bleed screws on both sides to press normally After the end of the inflation, loosen the deflated screw and then deflate, then take the inflation joint. To install the water pump, you need to put the water pump into the water. The more cold water, the better.

After the water pump is normally circulated, the electric air pump can be turned on Manually shut down after reaching the required pressure, the whole process needs attention, and it is forbidden to leave. 1 x set of 30MPa high pressure air pump.

2 x pressure relief screws. 1 x tank breather plug.

Durable MaterialBeautiful AppearanceEasy to Install. Nice and Practical, High Quality Packaging. Made of high quality material, Durable.

Creative design, durable material, beautiful appearance.


220V 1.8KW High Pressure Diving Breath Air Pump Air Compressor 2800r/min 30MPA    220V 1.8KW High Pressure Diving Breath Air Pump Air Compressor 2800r/min 30MPA